790006

E145 electronic control board

The E145 can control one or two swinging door operators, a sliding gearmotor or mixed systems of swinging-sliding doors.

It is compatible with all receivers (3-pin or 5-pin or external) and all photocells (BUS as well as traditional).

This product can become SAFE &GREEN with appropriate accessories

Có thể bạn quan tâm: 790286 790284 790005

THÔNG SỐ KỸ THUẬT

Model	E145
Power Supply Voltage	Switching power supply 90V~ to 260V~ 50(60) Hz
Max Power	4W Stand-by, <2W with sleep mode (programmable via PC/MAC) W
Max. engine power	800W
Max accessories load	500 mA 24V - 500 mA BUS 2easy
Electric lock max load	FAAC Lock (12V~ - 24V ) - non-FAAC 24V - 500 mA
Programming mode	LCD Display and buttons, by means of PC/MAC through USB-B connection
Status signalling	LCD Display and LED
Terminal board input	Open, Open pedestrian leaf, Stop (closed), BUS 2easy, Opening safety devices, Closing safety devices, Power supply + Earth, Opening and closing limit switch
Terminal boards output	Flashing light, Engines, 24V accessories power supply, 2 programmable(default OUTPUTS: LED and failsafe), 2 Electric lock controls
Rapid connector	XF 433/868 Module for OMNIDEC decoding, Connector for DECODER/MINIDEC/RP, USB-A, USB-B
Protection Fuses	1 (10A)
Operating ambient temperature	-20 °C ÷ +55 °C

FUNCTIONS (PROGRAMMING VIA DISPLAY AND BUTTONS)

Basic programming

Type of motors	Selectable (swing, sliding, mixed swing – sliding installation)
Operating logic	Semi-automatic, Semi-automatic stepped, Automatic safety device, Automatic with pause inversion, Automatic stepped, Automatic stepped safety device, Automatic, Automatic 1, Automatic with timer function, Semi-automatic B, Mixed (Pulse OP./Dead Man CL.), Dead man C, Custom (PC/MAC)
Pause time	Independently programmable after total or partial opening (from 0 to 9 min 50 sec)
Number of motors	Selectable
Thrust power	Adjustable on 50 levels for each motor independently
Encoder use	Selectable
Leaf delay time in closing	Programmable (from 0 to 1 min 30 sec)
Limit switch	limit switch function in opening and closing, selectable independently
Leaf delay time in closing	Programmable (from 0 to 1 min 30 sec)
BUS 2-Easy device registration	Selectable
Motor Power	1 and 2 (independently)
Working time learning	Simple self-learning (max 4 min and 10 sec). Self-learning of working and deceleration time of the two leaves thanks to a single complete work cycle) The SAFEcoder absolute encoder learns the open/closed/slowdown positions of the gate
Advanced programming
Maximum power at initial thrust	Selectable
Reverse stroke and ram stroke	Independently selectable (facilitating the coupling and uncoupling of the electric lock)
Leaf delay in opening	Selectable
Leaf 1 deceleration	Programmable, percentage of the total stroke (from 0% to 99%)
Leaf 2 deceleration	Programmable, percentage of the total stroke (from 0% to 99%)
Storable codes	Number of radio codes programmed on OMINIDEC through XF Module display
Pre-Flashing
Photocell in closing	Selectable Function
ADMAP Function	Selectable
Anti-crushing sensitivity	Programmable there is an ENCODER (10 levels)
Mechanical stop angle search	Selectable if the ENCODER is present
Additional work time	Selectable (if ENCODERS or limit switches are not present)
OUT 1 and OUT2 programming	Independently selectable (17 statuses each)
Service request	Selectable (if the programmed number of cycles is reached, the system activates an 8 sec pre-flashing before any movement)
Cycle count	Selectable (upgrade of a ''countdown'' - max setting 99,000 cycles)
File management through USB-A
Board software upload	Selectable
Board configuration upload	Selectable
Timer configuration upload	Selectable
Radio codes list upload	Selectable
Board configuration download	Selectable
Board timer download	Selectable
Board radio code download	Selectable
USB-B
Connection to PC/MAC for programming via EASYBOARD software (free download from the FAAC website www.faacgroup.com).	Allows for: programming of the equipment and monitoring of the functional status of both the board and the connected devices, programming of the timer function (operating logic setting in relation to time), upgrading and downloading directly from PC/MAC without the need for external devices, password protecting access to control board programming.